Roll and Tilt Radian connected to differents receivers

Discussion in 'Radian' started by Cedric Duchateau, Mar 10, 2013.

  1. Cedric Duchateau

    Cedric Duchateau New Member

    Joined:
    Jan 26, 2013
    Messages:
    13
    Likes Received:
    0
    Hi,

    I got a 2 axis CS gimbal with radians, one GR24 to the FC board and one Spektrum Sat to the roll radian.

    I would like to know if it was possible to connect the roll radian to the GR24 (or to the FC) for "On or Off mode" and the tilt radian to the spektrum sat.

    Or maybe is it possible to add a mode (with a combination of switchs on the transmitter)
    1. Off
    2. Stab
    3. Stab with slew (Stab Roll and Tilt)
    4. Stab with slew (Stab only on Tilt)
    Thank you for your help.
     
  2. Gary Haynes

    Gary Haynes Administrator
    Staff Member

    Joined:
    Jul 6, 2012
    Messages:
    5,211
    Likes Received:
    460
    Cedric can you explain what you are trying to do?
     
  3. Cedric Duchateau

    Cedric Duchateau New Member

    Joined:
    Jan 26, 2013
    Messages:
    13
    Likes Received:
    0
    I just want to be able to turn ON or OFF the roll stabilisation keeping the tilt stabilisation and slew ON.
     
  4. Andy Johnson-Laird

    Andy Johnson-Laird Administrator
    Staff Member

    Joined:
    Jul 31, 2012
    Messages:
    10,366
    Likes Received:
    1,162
    Why not use two separate channels for the Mode control, one for roll, one for tilt?

    Andy,
     
  5. Cedric Duchateau

    Cedric Duchateau New Member

    Joined:
    Jan 26, 2013
    Messages:
    13
    Likes Received:
    0
  6. Cedric Duchateau

    Cedric Duchateau New Member

    Joined:
    Jan 26, 2013
    Messages:
    13
    Likes Received:
    0
    Just kidding! Thanx Andy.

    I'm just feeling so dumb now!
     
  7. Andy Johnson-Laird

    Andy Johnson-Laird Administrator
    Staff Member

    Joined:
    Jul 31, 2012
    Messages:
    10,366
    Likes Received:
    1,162
    No need to feel dumb. Just remember you're not as dumb as I look. :)

    We all get mental blocks and can overlook those "Duh! (Slap palm of hand on forehead)" moments.

    Andy.
     
  8. Cedric Duchateau

    Cedric Duchateau New Member

    Joined:
    Jan 26, 2013
    Messages:
    13
    Likes Received:
    0
    Yeah, you must be right!

    Of course the "separate channels stuff" works fine. But what about if I want to be able to switch between Dual pilot setup and Single pilot setup. I read a lot of topics about it and this one kept my attention:

    It seems to be easy, but I don't know how to set this up. Maybe am I searching to far (again)?
     
  9. Cedric Duchateau

    Cedric Duchateau New Member

    Joined:
    Jan 26, 2013
    Messages:
    13
    Likes Received:
    0
    It's midnight, I'm tired but I want to resume my situation at this time.

    If dual setup mode:
    Pilot -> MX20 -> GR24 -> FC (Sumo via Output8)​
    Co-pilot -> DX6i -> Spektrum Sat -> Roll Radian -> Tilt Radian​
    Roll Radian powered by a 2S lipo via 6VBec.​
    "Separate channels stuff" for modes control.​

    If single setup mode:
    Pilot -> MX20 -> GR24 -> FC (Sumo via Output8)​
    -> Roll Radian -> Tilt Radian (MX20 input 9 -> Ctrl10 and Tilt Radian Slew = 9)​
    Roll Radian powered by GR24.​

    It seems to work fine. I just need a test flight (tomorrow).
     

Share This Page