/dist/images/branding/favicon

Search Results

Search Again
Page 1 of 2
  1. Andrew-Crinson
    Post

    RADIAN Tilt Problem

    Hi everyone. Just wanted to let you all know that this problem is not resolved yet and at the moment John C has kindly offered to emulate the...
    Post by: Andrew-Crinson, Aug 25, 2013 in forum: Radian
  2. Andrew-Crinson
    Post

    RADIAN Tilt Problem

    Thanks Gary. We will give it a go but I have to remind myself again that we have had this all setup with Futaba in an effort to eliminate the rc....
    Post by: Andrew-Crinson, Aug 21, 2013 in forum: Radian
  3. Andrew-Crinson
    Post

    RADIAN Tilt Problem

    Cool. You had Me at twitching lol. I've just emailed Chris.
    Post by: Andrew-Crinson, Aug 21, 2013 in forum: Radian
  4. Andrew-Crinson
    Post

    RADIAN Tilt Problem

    It can't be that simple lol... Okay do we check the box on all Radian? Thanks Andy
    Post by: Andrew-Crinson, Aug 21, 2013 in forum: Radian
  5. Andrew-Crinson
    Post

    RADIAN Tilt Problem

    Hi Andy can you just explain that check box please?
    Post by: Andrew-Crinson, Aug 21, 2013 in forum: Radian
  6. Andrew-Crinson
    Post

    RADIAN Tilt Problem

    Great work Chris. But chaps before we start blaming the spektrum we have already tried Futaba S-BUS and had the same issue. What is interesting is...
    Post by: Andrew-Crinson, Aug 21, 2013 in forum: Radian
  7. Andrew-Crinson
    Post

    RADIAN Tilt Problem

    Okay Andy we will work from the tilt backwards. Good thinking. And the only other thing that's not been changed are the radian leads...
    Post by: Andrew-Crinson, Aug 20, 2013 in forum: Radian
  8. Andrew-Crinson
    Post

    RADIAN Tilt Problem

    Hi John. We have swapped out all radians (same firmware 1.03 41-99) and even changed from spektrum to Futaba S-BUS, and we still have the same...
    Post by: Andrew-Crinson, Aug 20, 2013 in forum: Radian
  9. Andrew-Crinson
    Post

    RADIAN Tilt Problem

    Thanks Andy.
    Post by: Andrew-Crinson, Aug 19, 2013 in forum: Radian
  10. Andrew-Crinson
    Post

    RADIAN Tilt Problem

    Hi Gary thanks for your question, its running at 5v
    Post by: Andrew-Crinson, Aug 19, 2013 in forum: Radian
  11. Andrew-Crinson
    Post

    RADIAN Tilt Problem

    Hi Andy thanks for this. I didn't know you could put power into port 2. I will give it a go. And yes the Spektrum satellite receiver is plugged...
    Post by: Andrew-Crinson, Aug 18, 2013 in forum: Radian
  12. Andrew-Crinson
    Post

    RADIAN Tilt Problem

    Just to clarify my opening statement "My tilt Radian has developed an issue" is incorrect. As after reviewing a few initial in flight test videos...
    Post by: Andrew-Crinson, Aug 18, 2013 in forum: Radian
  13. Andrew-Crinson
    Post

    RADIAN Tilt Problem

    Aircraft Type: SKYJIB 8 Gimbal Type: CS3 Radian Type: 3 axis Gimbal Power source: Tunnigy UBEC 7amp 5v with ferrite ring (3s lipo) Gimbal Radio...
    Post by: Andrew-Crinson, Aug 18, 2013 in forum: Radian
  14. Andrew-Crinson
    Post

    RADIAN Tilt Problem

    Hi Gary thanks for your comments. It sure does do it in flight as well. You could almost set your clock to it its that regular. Settings on the...
    Post by: Andrew-Crinson, Aug 17, 2013 in forum: Radian
  15. Andrew-Crinson
    Thread

    RADIAN Tilt Problem

    Hi Everyone. My Tilt radian has developed an issue. The Setup is a CS3 3 axis RADIAN configuration with Spektrum RC. With the system sitting...
    Thread by: Andrew-Crinson, Aug 17, 2013, 74 replies, in forum: Radian
  16. Andrew-Crinson
    Post

    Radian Firmware 1.03

    Thanks Gary I will give it a go.
    Post by: Andrew-Crinson, Jul 30, 2013 in forum: Radian
  17. Andrew-Crinson
    Post

    Radian Firmware 1.03

    Hi Gary. I can? At the moment, using a spektrum setup, I have a 3 position switch 0=Off 1=Passive (Stabilized tilt/roll) and 2=Slew (Pan & Tilt)...
    Post by: Andrew-Crinson, Jul 28, 2013 in forum: Radian
  18. Andrew-Crinson
    Post

    Radian Firmware 1.03

    Thanks John your a star. That's done the job. I don't want to keep you on but any thoughts on tilt and slew locking up? Its a spektrum setup. And...
    Post by: Andrew-Crinson, Jul 28, 2013 in forum: Radian
  19. Andrew-Crinson
    Post

    Radian Firmware 1.03

    Hi John hope your well. The Error is SerialNo Mismatch PAN RADIAN is 010A-0EDC:000000 ROLL Is 010A-0F21:000000 Tilt is 010A-0FC4:000000 Have I...
    Post by: Andrew-Crinson, Jul 28, 2013 in forum: Radian
  20. Andrew-Crinson
    Post

    Radian Firmware 1.03

    Hello again. I'm back in that old situation again when trying to update the firmware from 34-99. I had an issue with my pan slew and tilt slew...
    Post by: Andrew-Crinson, Jul 28, 2013 in forum: Radian
Showing results 1 to 20 of 30 Next >
Search Again
Page 1 of 2