/dist/images/branding/favicon

MoVI Pro FAQ

Discussion in 'MōVI Pro' started by Tabb Firchau, Nov 2, 2016.

  1. Tabb Firchau

    Tabb Firchau Administrator
    Staff Member

    Joined:
    Jun 28, 2012
    Messages:
    911
    Likes Received:
    472
  2. Ben Ruffell

    Ben Ruffell Active Member

    Joined:
    Jan 15, 2014
    Messages:
    229
    Likes Received:
    33
    Thanks Tabb, that is really helpful.

    I have printed out some copies to live in our various MoVI Kit's.

    http://www.overview.nz/
     
  3. Jordan Kahn

    Jordan Kahn New Member

    Joined:
    Dec 26, 2017
    Messages:
    5
    Likes Received:
    0
    Thanks for helping everyone. I can't figure out how to start a new post ... so... this post seems topical to my basic two questions I have.
    What is this wire? And what are these rolls?

    rolls.jpg wire.jpg


    Thank you kindly!
     
  4. Andy Johnson-Laird

    Andy Johnson-Laird Administrator
    Staff Member

    Joined:
    Jul 31, 2012
    Messages:
    10,383
    Likes Received:
    1,164
    Jordan:
    To start a new thread:
    1. Click on the "home" icon (a small house just to the left of "FORUMS" at the top of the screen.
    2. Select the forum in which you want to post the new thread.
    3. Then look for the button at the top right of the screen marked "Post New Thread" :)

    Hope this helps.
    Andy

    Forensic Software & sUAV / Drone Analyst : Photographer : Videographer : Pilot (Portland, Oregon, USA): Trees=2, Ground=1, Props=11. :(
    The Ground Is The Limit™
    ---------- Forensic Drone Analyst : Forensic sUAV Analyst : Forensic Unmanned Aircraft Analyst : Forensic Drone Expert
     
  5. Jordan Kahn

    Jordan Kahn New Member

    Joined:
    Dec 26, 2017
    Messages:
    5
    Likes Received:
    0
    Andy! Thank you! But what's the wire thing? Is it a strange pin connector convertor to some kind of a bluetooth antennae?

    And that roll of felt sticky sided stuff? What is that?
     
  6. Andy Johnson-Laird

    Andy Johnson-Laird Administrator
    Staff Member

    Joined:
    Jul 31, 2012
    Messages:
    10,383
    Likes Received:
    1,164
    The strange pin connector is (I suspect) what you use to force the Gimbal Control Unit to accept new firmware if, for some reason you brick it (e.g. interrupting a firmware upgrade).

    The felt sticky stuff is for either mounting accessories or for the camera gimbal....I've never actually figured it out!

    Andy

    Forensic Software & sUAV / Drone Analyst : Photographer : Videographer : Pilot (Portland, Oregon, USA): Trees=2, Ground=1, Props=11. :(
    The Ground Is The Limit™
    ---------- Forensic Drone Analyst : Forensic sUAV Analyst : Forensic Unmanned Aircraft Analyst : Forensic Drone Expert
     
    Jordan Kahn likes this.
  7. Jordan Kahn

    Jordan Kahn New Member

    Joined:
    Dec 26, 2017
    Messages:
    5
    Likes Received:
    0
    Hmmmm. I mean, the sticky stuff... there's a lot of it, too. Could it be for going between the rods and any accessories clamps to dampen vibrations or secure more tightly or protect the fit and finish of the O-ring or Mimic handlebars?
     
  8. Bryan Edmonds

    Bryan Edmonds Chief Mōvi Whisperer

    Joined:
    Jul 3, 2014
    Messages:
    254
    Likes Received:
    126
    A little late, but: That is grip tape if you want to wrap it where you hold the Mōvi Ring Pro. Like you would on a golf club or tennis racket.
     
  9. Bryan Edmonds

    Bryan Edmonds Chief Mōvi Whisperer

    Joined:
    Jul 3, 2014
    Messages:
    254
    Likes Received:
    126

Share This Page