/dist/images/branding/favicon

Radian Software

Discussion in 'Radian' started by Tabb Firchau, Sep 12, 2012.

  1. Arthur Vieira

    Arthur Vieira Flight Squad

    Joined:
    Jun 29, 2012
    Messages:
    185
    Likes Received:
    24
    Josh the Roll must be repositioned for the new software. I've discovered that yesterday. Haven't tried the Pan, the Tilt is the same.
    Just remove the Roll Radian from under the Gimbal and glue it to the gear with double side tape. :)
     
  2. Tabb Firchau

    Tabb Firchau Administrator
    Staff Member

    Joined:
    Jun 28, 2012
    Messages:
    911
    Likes Received:
    472
    Hi Arthur,

    The tilt, roll, and pan mounting are all different on the production version of the software. You should swap the module on tilt also so it is not backwards.

    Thanks again for the nice gifts from Brazil! Megan has the quati sitting on her desk right now ;)
     
    RcHeliPilot likes this.
  3. Arthur Vieira

    Arthur Vieira Flight Squad

    Joined:
    Jun 29, 2012
    Messages:
    185
    Likes Received:
    24
    Hum... Actually, now that you mentioned it. I had it installed backwards since day one :). I've installed it on the gear as the production unit is installed, and it has always worked perfectly.

    Glad you guys liked the package, I hope the sizes where right. :D
     
  4. Bob Wojda

    Bob Wojda Member

    Joined:
    Sep 13, 2012
    Messages:
    64
    Likes Received:
    1
    When I download the software and unzip there is only a .fw file. I think that's probably the firmware update. Is there another place for the GUI software?
    Thanks,

    Bob
     
  5. Tabb Firchau

    Tabb Firchau Administrator
    Staff Member

    Joined:
    Jun 28, 2012
    Messages:
    911
    Likes Received:
    472
    Hi Bob, all links should be good to go now

    Thanks!
     
  6. Arthur Vieira

    Arthur Vieira Flight Squad

    Joined:
    Jun 29, 2012
    Messages:
    185
    Likes Received:
    24
    Bob, on the page there are 4 links.
    1 - Instructions
    2 - Software
    3 - Firmware
    4 - Bootloader
    You got the #3. Get the #2.
     
  7. Tabb Firchau

    Tabb Firchau Administrator
    Staff Member

    Joined:
    Jun 28, 2012
    Messages:
    911
    Likes Received:
    472
    HI Arthur, this was our fault....we had a broken page for a few minutes. Bob must have looked just at the 'wrong' time!

    Thanks!

    Tabb
     
    RcHeliPilot likes this.
  8. Bob Wojda

    Bob Wojda Member

    Joined:
    Sep 13, 2012
    Messages:
    64
    Likes Received:
    1
    Thanks Tabb,

    That always seems to be the case, I'm always looking when I shouldn't be. Thanks for fixing it so fast.

    Bob
     
  9. Pavlos Antoniou

    Joined:
    Oct 6, 2012
    Messages:
    321
    Likes Received:
    18
    Isnt there a mac version??
     
  10. Arthur Vieira

    Arthur Vieira Flight Squad

    Joined:
    Jun 29, 2012
    Messages:
    185
    Likes Received:
    24
    Sorry, PC only, just like MK-Tools. But you can virtualize a Windows under MAC OS or use Boot Camp both will work.
     
  11. Ville Hyvönen - Helicam

    Joined:
    Jul 5, 2012
    Messages:
    16
    Likes Received:
    7
    Radian software runs otherwise nicely on my Mac / Mountain Lion / Parallels desktop 8 / Windows 7 - but it does not help my windows allergy at all that all the radio button graphics are distorted. Tried to play around with some windows graphics settings without any results. Anyhow if anyone has any ideas - and FF guys - Mac and iOS version, please pretty please! :)

    -v
    Snapshot 10:28:12 1:24 PM-2.jpeg
     
  12. Arthur Vieira

    Arthur Vieira Flight Squad

    Joined:
    Jun 29, 2012
    Messages:
    185
    Likes Received:
    24
    Ville,

    Try reducing the font size.
    Right click in the middle of the Desktop -> Personalize -> Display (lower left)
    Check if the "Smaller - 100%" option is marked.
    Also you can go into "Set custom text size (DPI)" - Left menu - and adjust the size. If the above option is marked try decreasing this a little.

    Good luck
     
  13. John Fox

    John Fox Member

    Joined:
    Nov 10, 2012
    Messages:
    30
    Likes Received:
    0
    I Can't get the software to run my netbook with XP. I have installed it on 3 win7 machines with no problem. Any one else using XP?
     
  14. Marc BRACELET

    Marc BRACELET Active Member

    Joined:
    Jul 10, 2012
    Messages:
    204
    Likes Received:
    27
    Yes, i'm runing radian software with XP on my old PC (Mac user for years) without any problem..
     
  15. Andy Johnson-Laird

    Andy Johnson-Laird Administrator
    Staff Member

    Joined:
    Jul 31, 2012
    Messages:
    10,383
    Likes Received:
    1,164
    Hi John: What actually happens on your Netbook? Does it crash right away or does it display one of those lovely "There has been an error, see if you can guess what's wrong" messages?

    Andy.
     
  16. André Cousin

    André Cousin New Member

    Joined:
    Oct 19, 2012
    Messages:
    20
    Likes Received:
    0
    I have also some problem with XP:
    - PC Software 1.0.1 is installing and run well.
    - During Setup of Bootloader programm I get the message "Setup cannoty continue because some system files are out of date on your system"

    I know XP is up to date but may be something else is bad but what?

    No problem at all with windows 7.
     
  17. Andy Johnson-Laird

    Andy Johnson-Laird Administrator
    Staff Member

    Joined:
    Jul 31, 2012
    Messages:
    10,383
    Likes Received:
    1,164
    I'll try installing under XP and report back.
    Andy.
     
  18. Andy Johnson-Laird

    Andy Johnson-Laird Administrator
    Staff Member

    Joined:
    Jul 31, 2012
    Messages:
    10,383
    Likes Received:
    1,164
    I installed both version 1.0 and then 1.01 of the Radian software under Windows XP [edit: I should have added "successfully" -- no problems.). It looks like the Radian software was written in Visual Basic, so there may be issues with some of components of VB if you're getting that "Setup cannot continue..." message.

    I did a Google search for you, using the text of that message and this may be relevant: http://support.microsoft.com/kb/831491
    It looks like, as I thought, it might be a problem with VB components on your system....but that's pure speculation.

    Andy.
     
  19. songxin

    songxin New Member

    Joined:
    Nov 23, 2012
    Messages:
    1
    Likes Received:
    0
    hi this is david from china, i bought a 3axis radian from hongkong, but the firmware is 1.02, if i use the 1.1 pcsoftware to change setting,it will show Time Out. today i try to upgrade the firmware to 1.03 but when i chose the file (download from your website),it will show <Invalid date format on input line 1>, could u send me the old pcsoftware for 1.02 firmware?or send me a new firmware(i download 5-6times from your website ,not works).
    this is my email songxin@263.net
    Thx
     

    Attached Files:

    • ???.jpg
      ???.jpg
      File size:
      4.9 KB
      Views:
      10
  20. Andy Johnson-Laird

    Andy Johnson-Laird Administrator
    Staff Member

    Joined:
    Jul 31, 2012
    Messages:
    10,383
    Likes Received:
    1,164
    Hi David:
    Check out this thread. It describes how to solve the problem. (Change Windows to run in English.)

    Andy.
     

Share This Page