Recent Content by Tony Larkin

  1. Tony Larkin
    Post

    Another Servos Smokes!

    Hi Guys, Following my posts about voltage reg. Can I swap my 6v/5a lipo regulator for a 5v/5a ubec? It's to power the gimbal servos and radians....
    Post by: Tony Larkin, Aug 14, 2013 in forum: 2 Axis Gimbal
  2. Tony Larkin
    Post

    Another Servos Smokes!

    Thanks Guys, What about the Radians? Can i simply swap my 6V regulator that feeds the gimbal for a 5V? Tony
    Post by: Tony Larkin, Jul 22, 2013 in forum: 2 Axis Gimbal
  3. Tony Larkin
    Post

    Another Servos Smokes!

    Hi Andy, Yeh, I opened the original and have seen the board. Looks like the chip that has burnt out? Wonder if there's a replacement for that!...
    Post by: Tony Larkin, Jul 22, 2013 in forum: 2 Axis Gimbal
  4. Tony Larkin
    Post

    Another Servos Smokes!

    Hi Gary, Yeh, I've seen this issue being discussed. Checked with a volt meter and i'm reading 6.04?!
    Post by: Tony Larkin, Jul 22, 2013 in forum: 2 Axis Gimbal
  5. Tony Larkin
    Thread

    Another Servos Smokes!

    Hi Guys, I am running the 2 axis gimbal on my CS6. Only actually used the gimbal twice and both times the roll servo has smoked itself! Both times...
    Thread by: Tony Larkin, Jul 22, 2013, 9 replies, in forum: 2 Axis Gimbal
  6. Tony Larkin
    Post

    GPS Help

    Thanks Gary, That makes sense and now i've heard it from yourself i'm ready to give it a try. Weather here in NW England is rubbish today! I'll...
    Post by: Tony Larkin, Jun 22, 2013 in forum: Cinestar 6
  7. Tony Larkin
    Thread

    GPS Help

    Hi Guys, I'm keen to try MK GPS modes and feel confident about how to use them. However, i'm not confident about how to exit a GPS mode/s? Stick...
    Thread by: Tony Larkin, Jun 22, 2013, 2 replies, in forum: Cinestar 6
  8. Tony Larkin
    Post

    CS6 Irratic motor speed

    I think this was something to do with the compass. I re-calibrated it and since then it's been fine! Tony
    Post by: Tony Larkin, Jun 22, 2013 in forum: Cinestar 6
  9. Tony Larkin
    Profile Post

    CS6, MK flightcontrol V2.1 & GPS. Freefly 2 axis gimbal, Graupner MX20, Canon 5D MKII, Fuji...

    CS6, MK flightcontrol V2.1 & GPS. Freefly 2 axis gimbal, Graupner MX20, Canon 5D MKII, Fuji S3pro, BMD Pocket Cinema Camera on order!
    Status Update by Tony Larkin, Jun 22, 2013
  10. Tony Larkin
    Post

    CS6 Irratic motor speed

    Andy, Thanks once again for your advice. Unfortunately, i'm working away a lot at the moment so time on the project is limited. For a few weeks...
    Post by: Tony Larkin, Jun 9, 2013 in forum: Cinestar 6
  11. Tony Larkin
    Post

    CS6 Irratic motor speed

    Hi Josh, The CS6 was built by a company here in England. However, when i took ownership of it, the software was out of date and i made the...
    Post by: Tony Larkin, Jun 8, 2013 in forum: Cinestar 6
  12. Tony Larkin
    Post

    MK Tool?

    Thanks for this William. I know what i'll be doing tomorrow!
    Post by: Tony Larkin, Jun 8, 2013 in forum: Software Solutions
  13. Tony Larkin
    Post

    CS6 Irratic motor speed

    Agreed, the frame rate does give an unusual look to a spinning rotor!! I'll try and get some decent audio at least. Tony
    Post by: Tony Larkin, Jun 5, 2013 in forum: Cinestar 6