/dist/images/branding/favicon

Recent Content by David Tivadze

  1. David Tivadze
    Post

    Vibrations

    Andy, Gary - thank You for Your care. I really will never start the motors with props attached indoors. Because , as You can see , the off-on...
    Post by: David Tivadze, Feb 24, 2015 in forum: Cinestar 8
  2. David Tivadze
    Post

    Vibrations

    Yes, Andy, everything was just vise versa Thanks again, specially for safety issues. In case I need to start motors with props indoor I will wear...
    Post by: David Tivadze, Feb 21, 2015 in forum: Cinestar 8
  3. David Tivadze
    Post

    Vibrations

    Andy: THANK YOU for Your Warning! I will take into account Your advise. Now. I was sure ( I do not know why) that Number 1 motor (RED Boom) should...
    Post by: David Tivadze, Feb 21, 2015 in forum: Cinestar 8
  4. David Tivadze
    Thread

    Vibrations

    Hi, Just finished my assembly of CS 8 HL. Today switch it on and ....... what the hell it could be? When I test motors with MKtools everything...
    Thread by: David Tivadze, Feb 21, 2015, 9 replies, in forum: Cinestar 8
  5. David Tivadze
    Post

    Heavy Lift Motors and not only

    Andy, No, the Flight Controller is mounted exactly as it should be ,with arrow looking directly to the boom N1. For FC board, fortunately there...
    Post by: David Tivadze, Nov 24, 2014 in forum: Cinestar 8
  6. David Tivadze
    Post

    How to connect the servo to the GR 16

    Here are some photos with the project "Cinestar8 with retractable landing gear" David
    Post by: David Tivadze, Nov 24, 2014 in forum: Cinestar 8
  7. David Tivadze
    Post

    Heavy Lift Motors and not only

    Thanks Dave, I will correct them immediately. David
    Post by: David Tivadze, Nov 24, 2014 in forum: Cinestar 8
  8. David Tivadze
    Post

    Heavy Lift Motors and not only

    Thanks, Gary , for Your response. I definitely will buy real FF hub plates , if You suppose, that deviation on the PD board may be an issue....
    Post by: David Tivadze, Nov 24, 2014 in forum: Cinestar 8
  9. David Tivadze
    Post

    Heavy Lift Motors and not only

    So, measurements done. Here is the deviation from the vertical direction 1 ------- -0.3° 2 ------- +0.5° 3 ------- +1.2° 4 ------- +0.2° 5...
    Post by: David Tivadze, Nov 24, 2014 in forum: Cinestar 8
  10. David Tivadze
    Post

    Heavy Lift Motors and not only

    Janne, thank You very much , I will try this app today. Hope it will help. By the way, when we say, 0° alignment , what deviation could be...
    Post by: David Tivadze, Nov 24, 2014 in forum: Cinestar 8
  11. David Tivadze
    Post

    Heavy Lift Motors and not only

    I made that propeller "disc" check today. Not at the fly, but on the table at home. Seems they are all in line with each other. At least with my...
    Post by: David Tivadze, Nov 23, 2014 in forum: Cinestar 8
  12. David Tivadze
    Post

    Heavy Lift Motors and not only

    Thank You very much, Andy. I definitely will check out this document, sure it will be very useful. Could You, or anybody else here, give me an...
    Post by: David Tivadze, Nov 23, 2014 in forum: Cinestar 8
  13. David Tivadze
    Thread

    Heavy Lift Motors and not only

    Hi, It is absolutely clear , that at some point most of us face with a problem of appropriate motor selection for our setup. I know, that there is...
    Thread by: David Tivadze, Nov 23, 2014, 24 replies, in forum: Cinestar 8